Lincoln-electric PIPELINER LN-23P User Manual

PIPELINER®LN-23PPortable Innershield Semiautomatic Wire FeederOPERATOR’S MANUALIM867-ANovember, 2006Safety Depends on YouLincoln arc welding an

A-3INSTALLATIONPIPELINER®LN-23PA-3WIRE DRIVE ROLLS AND GUIDE TUBESThe LN-23P is shipped with the proper drive rolls andguide tubes factory installed.

B-1OPERATIONB-1PRODUCT DESCRIPTIONThe K316L-5 / LN-23P is a lightweight, portable wire feedunit which includes calibrated wire speed control, voltagec

B-2OPERATIONPIPELINER®LN-23PB-2ADJUSTING WIRE FEED SPEED ANDVOLTAGESet the wire feed as specified in the procedures usingthe calibrated dial on the ba

C-1ACCESSORIESPIPELINER®LN-23PC-1OPTIONAL EQUIPMENTGUN AND CABLE ASSEMBLIESK2393-1 25’ INPUT CABLE ASSEMBLY.8-pin to 14-pin control cable attached to

D-1MAINTENANCED-1GUN AND CABLE MAINTENANCERemove spatter from tip after each ten minutes of arctime or as required.Replace worn contact tips and threa

D-2MAINTENANCEPIPELINER®LN-23PD-2CIRCUIT PROTECTIONCircuit Breaker – The 3.5 amp circuit breaker locatedon the rear of the unit normally trips only wh

E-1TROUBLESHOOTINGE-1PIPELINER®LN-23PIf for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, co

E-2TROUBLESHOOTINGE-2PIPELINER®LN-23PObserve all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test pro

E-3TROUBLESHOOTINGE-3PIPELINER®LN-23PObserve all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test pro

F-1DIAGRAMSF-1PIPELINER®LN-23PCRM33074 (8/01)14M14197H F G E C DF E D C B AFOR CODES BELOW 10892NOTE: This diagram is for reference only.

FOR ENGINEpowered equipment.1.a. Turn the engine off before troubleshooting and maintenancework unless the maintenance work requires it to be running.

F-2DIAGRAMSF-2PIPELINER®LN-23PS25419 DLN23-PSENSE LEAD (PIGTAIL)SENSE LEAD & CLAMPPOWER LEADCONTROL CABLEWARNINGCAN KILLELECTRIC SHOCKTurn off inp

F-3DIAGRAMSF-3PIPELINER®LN-23PS25869 ACONNECTION DIAGRAM: SAE 400 ENGINE WELDERS COMPATIBLE WITH LN-23P AND K2379-1 INTERFACE

F-4DIAGRAMSF-4PIPELINER®LN-23P K2379-1 SAE 400/LN 23P INTERFACE KIT13456264215*RELAY P.C. BOARD3215216046022B2A3132477767521607606605(J)(A)(D)(C)(H

F-5DIAGRAMSF-5PIPELINER®LN-23PFIELD CALIBRATION OF K-316 LN-23P P.C. BOARDS-169023-30-84M

NOTESPIPELINER®LN-23P

NOTESPIPELINER®LN-23P

WARNINGAVISO DEPRECAUCIONATTENTIONWARNUNGATENÇÃOSpanishFrenchGermanPortugueseJapaneseChineseKoreanArabicREAD AND UNDERSTAND THE MANUFACTURER’S INSTRUC

WARNINGAVISO DEPRECAUCIONATTENTIONWARNUNGATENÇÃOSpanishFrenchGermanPortugueseJapaneseChineseKoreanArabicLEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE

• Sales and Service through Subsidiaries and Distributors Worldwide •Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB

iiSAFETYiiARC RAYS can burn.4.a. Use a shield with the proper filter and coverplates to protect your eyes from sparks andthe rays of the arc when weld

FOR ELECTRICALLYpowered equipment.8.a. Turn off input power using the disconnectswitch at the fuse box before working onthe equipment.8.b. Install equ

ivSAFETYivPRÉCAUTIONS DE SÛRETÉPour votre propre protection lire et observer toutes les instructionset les précautions de sûreté specifiques qui parra

vvThank Youfor selecting a QUALITY product by Lincoln Electric. We want youto take pride in operating this Lincoln Electric Company product••• as much

viviTABLE OF CONTENTSPageInstallation...

TEMPERATURE RANGEOPERATION: - 30oCo* to +40oC (- 22oF to +104oF)STORAGE: - 40oC to +40oC (- 40oF to +104oF)ENVIRONMENTAL RATINGENVIRONMENTAL RATINGA-1

A-2INSTALLATIONA-2PIPELINER®LN-23PINPUT CABLEThe standard input cable between the LN-23P and thepower source consists of a control cable and an elec-t