INVERTEC V350-PRO (CE)OPERATOR’S MANUALFor use with machines Code; 10670 IM708January, 2001Safety Depends on YouLincoln arc welding and cuttingequi
V350-PRO (CE)A-1INSTALLATION A-1TECHNICAL SPECIFICATIONS - INVERTEC V350-PRO (CE)INPUT AC VOLTAGE & DC OUTPUTOUTPUT CABLES, CONNECTIONS AND LIMI
A-2INSTALLATION A-2SELECT SUITABLE LOCATIONThe Invertec V350-PRO (CE) will operate in harshenvironments. Even so, it is important that simple pre-ve
A-3INSTALLATION A-3V350-PRO (CE) LN-10 Connection Instructions• Turn the Invertec power switch "off".• Connect the K1505 control cable f
A-4INSTALLATION A-4V350-PRO (CE) PARALLEL OPERATIONThe V350-PRO (CE) are operable in parallel in CCmode. For best results, the currents of each mac
B-1OPERATIONV350-PRO (CE) B-1SAFETY PRECAUTIONSELECTRIC SHOCK can kill.• Do not touch electrically live parts orelectrode with skin or wet clothing.•
B-2OPERATIONB-25. THERMAL• This status light indicates when the power sourcehas been driven into thermal overload. If the outputterminals were "
B-3OPERATIONB-3• The Arc Control regulates the relative Slope of theprocess. Slope dynamically controls the force thearc has to penetrate an open roo
B-4OPERATIONB-4TIG mode• The remote will default to the 6-pin amphenol if aremote control is connected to the 6-pin amphenoland one of the 14-pin amph
B-5OPERATIONB-5AUXILIARY POWER• 115VAC, 42VAC and 24VAC power is availablefrom the two 14-pin amphenols on the rear of theunit. (K1728-2 Construction
C-1ACCESSORIESC-1OPTIONS / ACCESSORIES"CE" VERSION – K1728-3• The "CE" version is the Factory version with theaddition of power li
FOR ENGINEpowered equipment.1.a. Turn the engine off before troubleshooting and maintenancework unless the maintenance work requires it to be running.
D-1MAINTENANCED-1VISUAL INSPECTIONClean interior of machine with a low pressure airstream. Make a thorough inspection of all compo-nents. Look for s
E-1TROUBLESHOOTINGE-1V350-PRO (CE)If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, conta
E-2TROUBLESHOOTINGE-2V350-PRO (CE)If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, conta
E-3TROUBLESHOOTINGE-3V350-PRO (CE)Observe all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test proced
E-4TROUBLESHOOTINGE-4V350-PRO (CE)Observe all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test proced
E-5TROUBLESHOOTINGE-5V350-PRO (CE)Observe all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test proced
F-1DIAGRAMSF-1V350-PRO (CE)TURN THE POWER SWITCH OF THE WELDING POWERSOURCE "OFF" BEFORE INSTALLING PLUGS ON CABLESOR WHEN CONNECTING OR DIS
F-2DIAGRAMSF-2V350-PRO (CE)N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.N.B. DIAGRAM SHOWS ELECTRODE POSITIVE. TO CHA
F-3DIAGRAMSF-3V350-PRO (CE)N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.N.B. DIAGRAM SHOWS ELECTRODE POSITIVE. TO CHA
F-4DIAGRAMSF-4V350-PRO (CE)N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.N.B. DIAGRAM SHOWS ELECTRODE POSITIVE. TO CHA
iiSAFETYiiARC RAYS can burn.4.a. Use a shield with the proper filter and coverplates to protect your eyes from sparks andthe rays of the arc when weld
F-5DIAGRAMSF-5V350-PRO (CE)Only qualified persons should install, use orservice this machine.using the disconnect switch at the fuse boxWARNINGTurn of
F-6DIAGRAMSF-6V350-PRO (CE)Only qualified persons should install, use orservice this machine.using the disconnect switch at the fuse boxWARNINGTurn of
F-7DIAGRAMSF-7V350-PRO (CE)NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific
F-8DIAGRAMSF-8V350-PRO (CE)14.7912.443.4421.6027.825.5010.00MOUNTING HOLE LOCATIONSM1952713.101/4-20 NUT (4 PLACES)NOTE: MOUNTING SCREWS CA8/00N NOT
NOTES
Now Available...12th EditionThe Procedure Handbook of Arc WeldingWith over 500,000 copies of previous editions publishedsince 1933, the Procedure Hand
WARNINGAVISO DEPRECAUCIONATTENTIONWARNUNGATENÇÃOSpanishFrenchGermanPortugueseJapaneseChineseKoreanArabicREAD AND UNDERSTAND THE MANUFACTURER’S INSTRUC
WARNINGAVISO DEPRECAUCIONATTENTIONWARNUNGATENÇÃOSpanishFrenchGermanPortugueseJapaneseChineseKoreanArabicLEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE
• Sales and Service through Subsidiaries and Distributors Worldwide •Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB
FOR ELECTRICALLYpowered equipment.8.a. Turn off input power using the disconnectswitch at the fuse box before working onthe equipment.8.b. Install equ
ivSAFETYivPRÉCAUTIONS DE SÛRETÉPour votre propre protection lire et observer toutes les instructionset les précautions de sûreté specifiques qui parra
vSAFETYvV350-PRO (CE) L10093 3-1-96HConformancestandard: EN 50 199 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment.
viSAFETYviV350-PRO (CE)The size of the surrounding area to be considered will depend on the structure of the building and otherMethods of Reducing Emi
Thank Youfor selecting a QUALITY product by Lincoln Electric. We want youto take pride in operating this Lincoln Electric Company product••• as much p
viiiviiiTABLE OF CONTENTSPageInstallation ..........................Secti
Comments to this Manuals