Lincoln Electric SVM150-A User Manual download pdf (Page 26)

OPTIONS/ACCESSORIES

FIELD INSTALLED OPTIONS

The following options/accessories are available for

your Ranger 250 from your local Lincoln distributor.

K957-1 HEAVY DUTY, TWO-WHEEL TRAILER FOR

SMALL WELDERS - For road, off-road and in-plant

and yard towing. (For highway use, consult applicable

federal, state and local laws regarding requirements for

brakes, lights, fenders, etc.)

K1737-1 FOUR-WHEEL ALL-TERRAIN UNDERCAR-

RIAGE - For moving by hand.

K1770-1 UNDERCARRIAGE (FACTORY) - For mov-

ing by hand on a smooth surface. One or two gas

cylinders can be mounted on the rear of the undercar-

riage with the installation of K1745-1 Cylinder

Holder(s).

K1739-1 CABLE CARRIER KIT - For use on K1737-1

and K1770-1 Undercarriages.

K1745-1 SINGLE GAS CYLINDER HOLDER - For use

on K1770-1 Undercarriage. One or two may be

installed on an undercarriage.

K1788-1 ROLL CAGE - Gives added damage protec-

tion.

K886-2 CANVAS COVER - Protects machine when

not in use.

S24647 SPARK ARRESTER - Mounts inside exhaust

pipe.

K702 ACCESSORY KIT - Accessory set includes 35 ft.

(10.7 meters) 2 AWG electrode cable, 30 ft. (9.1

meters) 2 AWG work cable, headshield with No. 12 fil-

ter, GC300 work clamp and Cooltong 300 electrode

holder. Cables are rated at 250 amps, 40% duty cycle.

K857 28 ft. (8.5m) or K857-1 100 ft. (30.4m)

REMOTE CONTROL - Portable control provides same

dial range as the output control on the welder. Has a

convenient 6-pin plug for easy connection to the

welder.

K1690-1 GFCI RECEPTACLE KIT - Includes one UL

approved 120 volt ground fault circuit interrupter duplex

type receptacle with cover and installation instructions.

Replaces the factory installed 120V duplex receptacle.

Each receptacle of the GFCI Duplex is rated at 20

amps. The maximum total current from the GFCI

Duplex is limited to 20 amps. Two kits are required.

K802-N POWER PLUG KIT - Provides four 120 volt

plugs rated at 20 amps each and one dual voltage, full

KVA plug rated at 120/240 volts, 50 amps.

K802-R POWER PLUG KIT - Provides four 120 volt

plugs rated at 15 amps each and one dual voltage, full

KVA plug rated at 120/240 volts, 50 amps.

T12153-9 50 AMP, 120/240V POWER PLUG -

Provides one dual voltage plug for full KVA power.

TIG WELDING ACCESSORIES

K1783-9 TIG TORCH - For TIG welding with shielding

gas. Includes 25 feet of cable.

K963-2 - Hand Amptrol.

K870 - Foot Amptrol.

NOTE: TIG welding requires a Magnum™ TIG Gun,

appropriate Magnum Parts Kit and argon gas.

SEMIAUTOMATIC FCAW AND MIG

WELDING ACCESSORIES

LN-25 WIRE FEEDER K449 - This portable unit pro-

vides CC/CV for flux-cored arc welding (FCAW) and

metal inert gas welding (MIG). Includes a gas solenoid

and an internal contactor that allows across-the-arc

operation with no control cable. The LN-25 provides a

“cold” electrode until the gun trigger is pressed. For

voltage control at the feeder, a K444-1 Remote Voltage

Control Kit or K857 Remote Control is required. Refer

to connection instructions later in this section.

LN-7 OR LN-8 WIRE FEEDER - Semiautomatic, con-

stant speed wire feeders.

NOTE: Gas-shielded welding requires a Magnum Gun.

Gasless welding requires an Innershield Gun.

LN-742 WIRE FEEDER - A semiautomatic wire feeder

with “cold” electrode. Refer to connection instructions

later in this section.

MAGNUM SPOOL GUN (K487-25) - A lightweight,

semiautomatic wire feeder for aluminum welding with

argon gas. Has built-in remote wire speed control in

the handle. Requires the K488 SG Control Module.

Refer to connection instructions later in this section.

SG CONTROL MODULE (K488) - Controls wire speed

and gas flow. Provides the required control interface

between the Ranger 250 and the K487-25 Magnum

Spool Gun. Requires the K691-10 Input Cable.

K444-1 REMOTE VOLTAGE CONTROL - Provides

voltage adjustment control at the feeder. Includes 25

feet of cable.

K126-2 INNERSHIELD GUN - For gasless welding.

Includes 15 feet of cable.

K470-2 MAGNUM GUN CONNECTOR KIT - For gas-

shielded welding.

K466-1 MAGNUM GUN CONNECTOR KIT - For con-

necting the Magnum 300 MIG Gun to the feeder for

gas-shielded welding.

ACCESSORIES

C-2 C-2

RANGER 250

Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC

Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 133 134

Comments to this Manuals

No comments

Lincoln Electric SVM150-A User Manual Page 26

Comments to this Manuals

Related products and manuals for Welding System Lincoln Electric SVM150-A