LN -23PPortable Innershield Semiautomatic Wire FeederOPERATOR’S MANUALIM311-ENovember, 2009Safety Depends on YouLincoln arc welding and cuttingequipme
• Other Power Sources: Mount the Adapter Kit to theside of the power source or some convenient locationso its control cable can be connected to th
B-1OPERATIONB-1PRODUCT DESCRIPTIONThe K316L-[ ] / LN™-23P is a lightweight, portable wire feedunit which includes calibrated wire speed control, vol
B-2OPERATIONLN™-23PB-22. Remove compartment cover along with plastic wirereel brake and reel cover. Pull wire end from spooland route it through the l
B-3OPERATIONB-3DRIVE ROLL PRESSUREThe drive roll pressure is pre-set at the factory forproper feeding. If the idle roll tension must be relievedtemp
C-1ACCESSORIESLN™-23PC-1OPTIONAL EQUIPMENTGUN AND CABLE ASSEMBLIESK350 ADAPTER KITRequired when using the LN™-23P on any constantvoltage power source.
D-1MAINTENANCED-1GUN AND CABLE MAINTENANCERemove spatter from tip after each ten minutes of arctime or as required.Replace worn contact tips and th
D-2MAINTENANCELN™-23PD-2CIRCUIT PROTECTIONCircuit Breaker – The 3.5 amp circuit breaker locatedon the rear of the unit normally trips only when anov
E-1TROUBLESHOOTINGE-1If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact yourLocal
E-2TROUBLESHOOTINGE-2LN™-23PObserve all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test procedures o
E-3TROUBLESHOOTINGE-3LN™-23PObserve all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test procedures o
FOR ENGINEpowered equipment.1.a. Turn the engine off before troubleshooting and maintenancework unless the maintenance work requires it to be running.
F-1DIAGRAMSF-1LN™-23PNOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagra
F-2DIAGRAMSF-2LN™-23P M17514 12-0113456264 215*RELAY P.C. BOARD31CR21521609608610604B60775BA60875A75B476A76B6026047576775216026047576775216022CRBA60
F-3DIAGRAMSF-3LN™-23PCRM33074 (8/01)14M14197H F G E C DF E D C B AFOR CODES BELOW 10892NOTE: This diagram is for reference only. It may n
F-4DIAGRAMSF-4LN™-23PNOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagra
F-5DIAGRAMSF-5LN™-23PNOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagra
F-6DIAGRAMSF-6LN™-23PNOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagra
F-7DIAGRAMSF-7LN™-23PNOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagra
F-8DIAGRAMSF-8LN™-23PNOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagra
F-9DIAGRAMSF-9LN™-23PNOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagra
F-10DIAGRAMSF-10LN™-23PNOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diag
iiSAFETYiiARC RAYS can burn.4.a. Use a shield with the proper filter and coverplates to protect your eyes from sparks andthe rays of the arc when weld
F-11DIAGRAMSF-11LN™-23PNOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diag
F-12DIAGRAMSF-12LN™-23PNOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diag
F-13DIAGRAMSF-13LN™-23PFIELD CALIBRATION OF K-316 LN™-23P P.C. BOARDS-169023-30-84M
WARNINGAVISO DEPRECAUCIONATTENTIONWARNUNGATENÇÃOSpanishFrenchGermanPortugueseJapaneseChineseKoreanArabicREAD AND UNDERSTAND THE MANUFACTURER’S INSTRUC
WARNINGAVISO DEPRECAUCIONATTENTIONWARNUNGATENÇÃOSpanishFrenchGermanPortugueseJapaneseChineseKoreanArabicLEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE
• Sales and Service through Subsidiaries and Distributors Worldwide •Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB
iiiSAFETYiiiFOR ELECTRICALLYpowered equipment.8.a. Turn off input power using the disconnectswitch at the fuse box before working onthe equipment.8.b.
ivSAFETYivPRÉCAUTIONS DE SÛRETÉPour votre propre protection lire et observer toutes les instructionset les précautions de sûreté specifiques qui parra
vvThank Youfor selecting a QUALITY product by Lincoln Electric. We want youto take pride in operating this Lincoln Electric Company product••• as much
viviTABLE OF CONTENTSPageInstallation...
TEMPERATURE RANGEOPERATION: - 30oCo* to +40oC (- 22oF to +104oF)STORAGE: - 40oC to +40oC (- 40oF to +104oF)ENVIRONMENTAL RATINGOPERATING ARC VOLTAGECo
A-2INSTALLATIONA-2LN™-23PINPUT CABLE:For K316L-1 (6 pin connector)The standard 25 foot input cable between the LN™-23P and the power source (with a
Comments to this Manuals