RED-D-ARCEX350ie (CE)IM980November, 2008Red-D-Arc Spec-Built Welding EquipmentThisRED-D-ARCwelder is built toRED-D-ARC Extreme Dutydesign specificatio
EX350ie (CE) (RED-D-ARC) A-1INSTALLATION A-1TECHNICAL SPECIFICATIONS - EX350ie (CE) (RED-D-ARC)INPUT AT RATED OUTPUTOUTPUT CABLES, CONNECTIONS AND L
A-2INSTALLATION A-2SELECT SUITABLE LOCATIONThe EX350ie (CE) will operate in harsh environments.Even so, it is important that simple preventative mea
A-3INSTALLATION A-3EX350ie (CE) (RED-D-ARC) LN-15 Connection Instructions • Turn the EX350ie (CE)power switch "off".• Connect the electr
A-4INSTALLATION A-4EX350ie (CE) (RED-D-ARC) PARALLEL OPERATIONThe EX350ie (CE) are operable in parallel in CCmode. For best results, the currents o
B-1OPERATIONEX350ie (CE) (RED-D-ARC) B-1SAFETY PRECAUTIONSELECTRIC SHOCK can kill.• Do not touch electrically live parts orelectrode with skin or wet
B-2OPERATIONB-25. THERMAL• This status light indicates when the power sourcehas been driven into thermal overload. If the out-put terminals were &quo
B-3OPERATIONB-3• The Arc Control regulates the Arc Force to adjust theshort circuit current. The minimum setting (-10) willproduce a "soft"
B-4OPERATIONB-4TIG mode• The remote will default to the 6-pin MS-style if aremote control is connected to the 6-pin MS-styleand to the 14-pin MS-style
C-1ACCESSORIESC-1OPTIONS / ACCESSORIES• The EX350ie (CE) provides the hardware to powerand connect to 24 or 42 wire feeders.K857 Remote Output Control
D-1MAINTENANCED-1VISUAL INSPECTIONClean interior of machine with a low pressure airstream. Make a thorough inspection of all compo-nents. Look for s
EX350ie (CE) (RED-D-ARC)FOR ENGINEpowered equipment.1.a. Turn the engine off before troubleshooting and maintenancework unless the maintenance work re
E-1TROUBLESHOOTINGE-1EX350ie (CE)(RED-D-ARC)If for any reason you do not understand the test procedures or are unable to perform the tests/repairs saf
E-2TROUBLESHOOTINGE-2If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact yourLocal
E-3TROUBLESHOOTINGE-3Observe all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test procedures or are u
E-4TROUBLESHOOTINGE-4Observe all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test procedures or are u
E-5TROUBLESHOOTINGE-5Observe all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test procedures or are u
F-1DIAGRAMSF-1EX350ie (CE) (RED-D-ARC) TURN THE POWER SWITCH OF THE WELDING POWERSOURCE "OFF" BEFORE INSTALLING PLUGS ON CABLESOR WHEN CONNE
F-2DIAGRAMSF-2EX350ie (CE) (RED-D-ARC) N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.N.B. DIAGRAM SHOWS ELECTRODE POSIT
F-3DIAGRAMSF-3EX350ie (CE) (RED-D-ARC) N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.N.B. DIAGRAM SHOWS ELECTRODE POSIT
F-4DIAGRAMSF-4EX350ie (CE) (RED-D-ARC) N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.N.B. DIAGRAM SHOWS ELECTRODE POSIT
F-5DIAGRAMSF-5EX350ie (CE) (RED-D-ARC) Only qualified persons should install, use orservice this machine.using the disconnect switch at the fuse boxWA
EX350ie (CE) (RED-D-ARC)iiSAFETYiiARC RAYS can burn.4.a. Use a shield with the proper filter and coverplates to protect your eyes from sparks andthe r
F-6DIAGRAMSF-6EX350ie (CE)(RED-D-ARC)Only qualified persons should install, use orservice this machine.using the disconnect switch at the fuse boxWARN
F-7DIAGRAMSF-7NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a
F-8DIMENSION PRINTF-8EX350ie (CE) (RED-D-ARC) 14.7912.443.4421.6027.825.5010.00MOUNTING HOLE LOCATIONSM1952713.101/4-20 NUT (4 PLACES)NOTE: MOUNTING
NOTES EX350ie (CE) (RED-D-ARC)
WARNINGAVISO DEPRECAUCIONATTENTIONWARNUNGATENÇÃOSpanishFrenchGermanPortugueseJapaneseChineseKoreanArabicREAD AND UNDERSTAND THE MANUFACTURER’S INSTRUC
WARNINGAVISO DEPRECAUCIONATTENTIONWARNUNGATENÇÃOSpanishFrenchGermanPortugueseJapaneseChineseKoreanArabicLEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE
• Sales and Service through Subsidiaries and Distributors Worldwide •Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB
iiiSAFETYiiiEX350ie (CE) (RED-D-ARC)FOR ELECTRICALLYpowered equipment.8.a. Turn off input power using the disconnectswitch at the fuse box before work
ivSAFETYivEX350ie (CE) (RED-D-ARC)PRÉCAUTIONS DE SÛRETÉPour votre propre protection lire et observer toutes les instruc-tions et les précautions de sû
vSAFETYvEX350ie (CE) (RED-D-ARC)Electromagnetic Compatibility (EMC)ConformanceProducts displaying the CE mark are in conformity with European Communit
viSAFETYviEX350ie (CE) (RED-D-ARC)Electromagnetic Compatibility (EMC)The size of the surrounding area to be considered will depend on the structure of
viiviiThank Youfor selecting one of our QUALITY products. We want you to takepride in operating this product ••• as much pride as we have inbringing t
viiiviiiTABLE OF CONTENTSPageInstallation ..........................Secti
Comments to this Manuals