RED-D-ARCZR-8IM928January, 2007Red-D-Arc Spec-Built Welding EquipmentThis RED-D-ARC welder is built to RED-D-ARC Extreme Dutydesign specifications by
3. Proper placement of the equipment on the trailer toinsure stability side to side and front to back whenbeing moved and when standing by itself whil
A-4INSTALLATION ZR-8A-4WELDING OUTPUT CABLESWith the engine off, connect the electrode and workcables to the studs provided. These connectionsshould
NOTE: The welding electrode is energized at alltimes, unless an LN-25 with built-in contactor is used.If the output “CONTROL” is set below “3”, the LN
120 V DUPLEX RECEPTACLESThe 120V auxiliary power receptacles should only beused with three wire grounded type plugs or approveddouble insulated tools
A-7INSTALLATION ZR-8A-7TABLE lllELECTRICAL DEVICE USE WITH THE ZR-8.Type Common Electrical Devices Possible ConcernsResistive Heaters, toasters, inc
A-8INSTALLATION ZR-8A-8STANDBY POWER CONNECTIONSThe ZR-8 is suitable for temporary, standby, or emer-gency power using the engine manufacturer’s rec
240 Volt60 Hz.3-WireServicePOWERCOMPANYMETER240 VOLT120 VOLT120 VOLTLOADNNEUTRALBUSGROUNDPREMISESDISCONNECT ANDSERVICEOVERCURRENTPROTECTIONGNDNNOTE:
WELDER CONTROLS - FUNCTION ANDOPERATIONENGINE SWITCHThe engine switch is used to Start the Engine, SelectHigh Idle or Auto Idle while the engine is r
“ RANGE” SWITCHThe “Range” switch is used to select one of threeamperage ranges with generous overlap for Stick/TIGwelding, or one Wire Feed welding r
B-3OPERATIONB-3STARTING/SHUTDOWN INSTRUCTIONSSTARTING THE ENGINEBe sure all Pre-Operation Maintenance has been per-formed. Also, read the Engine Owner
FOR ENGINEpowered equipment.1.a. Turn the engine off before troubleshooting and maintenancework unless the maintenance work requires it to be running.
B-4OPERATIONB-4WELDING PROCESSFor any electrodes the procedures should be keptwithin the rating of the machine. For electrode infor-mation see the app
B-5OPERATIONB-5ZR-8SUMMARY OF WELDING PROCESSESCONTROL ELECTRODECABLE IDLE WHEN NOT
C-1ACCESSORIESC-1ZR-8OPTIONAL EQUIPMENT (Field Installed)K957-1 HEAVY DUTY, TWO WHEEL TRAILER FORSMALL WELDERS - For road, off-road and in-plantand y
C-2ACCESSORIESC-2ZR-8RECOMMENDED EQUIPMENTSTICKK704 Accessory Kit which includes:• Electrode Holder & Cable• Work Clamp & Cable• Headshield
Have qualified personnel do the maintenancework. Turn the engine off before working insidethe machine. In some cases, it may be necessaryto remove saf
D-2MAINTENANCED-2Use 4-stroke motor oil that meets or exceeds therequirements for API service classification SG or SH.Always check the API SERVICE lab
D-3MAINTENANCED-3ENGINE ADJUSTMENTSOVERSPEED IS HAZARDOUSThe maximum allowable high idle speed for thismachine is 3750 RPM, no load. Do NOT tamperwit
E-1TROUBLESHOOTINGE-1ZR-8If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact yourLo
E-2TROUBLESHOOTINGE-2ZR-8Observe all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test procedures or a
E-3TROUBLESHOOTINGE-3ZR-8Observe all Safety Guidelines detailed throughout this manualIf for any reason you do not understand the test procedures or a
iiSAFETYiiARC RAYS can burn.4.a. Use a shield with the proper filter and coverplates to protect your eyes from sparks andthe rays of the arc when weld
RED-D-ARC ZR-8 (KOHLER)F-1WIRING DIAGRAMF-1ZR-8NOTE: This diagram is for reference only. It may not be accurate for all machines covered by t
F-2DIAGRAMSF-2ZR-8ZR-8 / / L LN-15 AND LN-25 ACROSS T AND LN-25 ACROSS THE ARC CONNECTE ARC CONNECTION DIN DIAGRAMELECTRIC SHOCK can killDo not oper
F-3DIMENSION PRINTF-3ZR-8RED-D-ARC ZR-8 (KOHLER)M20267 C.0126.5930.279.09 9.0917.0021.228.80 30.0042.0022.1510.33CENTER OF GRAVITY WITH OIL INENGINE
WARNINGAVISO DEPRECAUCIONATTENTIONWARNUNGATENÇÃOSpanishFrenchGermanPortugueseJapaneseChineseKoreanArabicREAD AND UNDERSTAND THE MANUFACTURER’S INSTRUC
WARNINGAVISO DEPRECAUCIONATTENTIONWARNUNGATENÇÃOSpanishFrenchGermanPortugueseJapaneseChineseKoreanArabicLEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE
• Sales and Service through Subsidiaries and Distributors Worldwide •Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB
FOR ELECTRICALLYpowered equipment.8.a. Turn off input power using the disconnectswitch at the fuse box before working onthe equipment.8.b. Install equ
Mar. ‘93ivSAFETYivPRÉCAUTIONS DE SÛRETÉPour votre propre protection lire et observer toutes les instructionset les précautions de sûreté specifiques q
vvThank Youfor selecting a QUALITY product by Lincoln Electric. We want youto take pride in operating this Lincoln Electric Company product••• as much
viviTABLE OF CONTENTSPageInstallation...
A-1INSTALLATION ZR-8A-1TECHNICAL SPECIFICATIONS ZR-8 (K2392-2)INPUT - GASOLINE ENGINERATED OUTPUT @ 104°F (40°C)- WELDERHEIGHT WIDTH DEPTH WEIGHT3
A-2INSTALLATION ZR-8A-2SAFETY PRECAUTIONSMACHINE GROUNDINGBecause this portable engine driven welder or genera-tor creates its own power, it is not
Comments to this Manuals